Home
Tab Content
  • Norv's Avatar
    15-02-2019, 06:43 PM
    You've got such a way with words Karl! But what you said is bang on. Sent from my Mi MIX 2 using Tapatalk
    2902 replies | 231084 view(s)
  • Norv's Avatar
    13-02-2019, 05:58 PM
    Norv replied to a thread Further EP3 Remaps in Engine & ECU
    The kpro has memory which will store data, but it is fairly limited to what it will show live. Personally I have gone for an aem failsafe gauge which...
    3 replies | 90 view(s)
  • Norv's Avatar
    10-02-2019, 12:29 PM
    Jesse mapped my Rotrex, really happy with it. He's really helpful and not just there to take your money which is always reassuring. Bet you can't...
    283 replies | 9655 view(s)
  • Norv's Avatar
    08-02-2019, 04:13 PM
    Norv replied to a thread K100 ECU and Remap in Engine & ECU
    Harry I genuinely think you'd be better off keeping the inlet manifold money for a LSD so you can use the extra power. They make a huge difference to...
    98 replies | 2392 view(s)
  • Norv's Avatar
    07-02-2019, 09:31 PM
    Norv replied to a thread K100 ECU and Remap in Engine & ECU
    http://www.tegiwaimports.com/blog/k-series-intake-dyno-face-off/ Here's a good article to read. M2 manifold is meant to be close to rbc...
    98 replies | 2392 view(s)
  • Norv's Avatar
    05-02-2019, 07:37 PM
    Norv replied to a thread Oil in Civic Type R (FK2)
    I'm sure most manufacturers actually estimate the oil temp by usuaing coolant temp readings. So most aren't much use when you'd want them anyway,...
    16 replies | 430 view(s)
  • Norv's Avatar
    04-02-2019, 08:04 PM
    Best bet is speak to some local recovery firms. I have a friend who does it on the side, but he's in Dorset so the miles will add up a bit too much...
    9 replies | 191 view(s)
  • Norv's Avatar
    04-02-2019, 05:32 PM
    Tgm are a good choice, they're very busy though I believe so maybe a few weeks to wait. Sent from my Mi MIX 2 using Tapatalk
    9 replies | 191 view(s)
  • Norv's Avatar
    03-02-2019, 02:53 PM
    I run poly exhaust rubbers for mine but only to stop the 3 inch knocking on everything. The knocking has stopped and I haven't found any downsides...
    116 replies | 6677 view(s)
  • Norv's Avatar
    02-02-2019, 02:55 PM
    Norv replied to a thread K100 ECU and Remap in Engine & ECU
    It was just the wasted time that I'd spent trying to fix the car that was most annoying. If they'd said they had heard similar problems I'd have got...
    98 replies | 2392 view(s)
  • Norv's Avatar
    01-02-2019, 09:37 PM
    Norv replied to a thread Nidge's Cosmic EP3 in Members' Cars
    Was the tester blind?! Jokes. Always nice to have the ticket. No matter how certain you are it will get it. Sent from my Mi MIX 2 using Tapatalk
    263 replies | 26141 view(s)
  • Norv's Avatar
    29-01-2019, 07:45 PM
    Their ecu isn't mappable unfortunately so you need to connect a daughter board to the ecu so it knows where to read the map file. These boards are...
    10 replies | 391 view(s)
  • Norv's Avatar
    29-01-2019, 06:20 PM
    You're best bet for efi would be a postal service to cpl with their reflash map (which isn't good) on your ecu and then drive to efi and get them to...
    10 replies | 391 view(s)
  • Norv's Avatar
    28-01-2019, 10:40 PM
    Norv replied to a thread K100 ECU and Remap in Engine & ECU
    Remember that vtec being lower doesn't mean more power. When mapped to the mods it is set where the high cam makes more power than the low cam. So...
    98 replies | 2392 view(s)
  • Norv's Avatar
    28-01-2019, 10:18 PM
    Norv replied to a thread K100 ECU and Remap in Engine & ECU
    It was my daily although very few miles. I had it for about 3 months I think. I had to delete the idle air assist valve just to get it to idle from...
    98 replies | 2392 view(s)
More Activity
About Norv

Basic Information

Statistics


Total Posts
Total Posts
700
Posts Per Day
0.43
Total Thanks
Total Thanks
10
  • Thanked 124 Times in 111 Posts
General Information
Last Activity
15-02-2019 06:46 PM
Join Date
18-08-2014