Search results

Under 3000 is fine. It only gets loud the fun side of 5000-6000 rpm

I am running the DC manifold with RM01A catback and can confirm the noise level does increase with the manifold. Not drastically though. Saying that i have felt it was not too loud for yeard but getting a bit old now and plan to switch catback to the legalis r to make it a little less loud...

Just had a similar pm from rootmoderators. !!

If you decide to go for the neuspeed one I am in the process of organising a group buy over on CTRO. Loads of info in the thread as well which you may find beneficial when deciding which one to get

I have the powerslots on the front and rear. Only got the rears as got them at a great price. Would not pay full price for them but they do look loads better but this is as far as the improvements go on the rear. Pics on car

I have the DC 4-2-1 mani and Fujitsubo RM01A catback and i would not say it is quiet. It is not too bad at low revs but give it some and it is loud. Gets a bit drowney on the m/way.

Can get the JDM ARBs as well - Front £70 Rear £63

Group buy is up and running on CTRO. £86 inc postage.

Get the genuine Honda ones. You can make the ones from USA fit but they need new brackets fabricated as people have said already. I fitted a set of genuine fogs to mine so can help out with any Qs re fitting. Quite easy to do, the only problems are locating the plug right at the back of the...

I am in the process of setting up a group buy on these. Will hopefully be about £100 a set. Anyone interested? Also, anyone know the Honda part code so I can check they are the correct ones?

Everything is fitted to the car with the exception of the header which should be going on this week. KPRO is installed and currently mapped to Spoon N1 and B pipe. Just want it mapped to GruppeM, Fuji RM01 and DC header/decat.

Is there anywhere in the south east that will do the 2 hour tuning of KPRO for around £150 mark? CPL/Abbey/TDI south have all removed this option and only offer the £350 full tune which I cant really afford at the moment.

Had Kpro fitted yesterday - :D :D :D :D It has been mapped by CPL for Spoon N1/B pipe and AEM filter. Vtec set to 5300.(seems quite high) Revs 8600. The mods I have on the car are Gruppe M and Fujitsubo RM01 cat back. I have a DC manifold/decat to go on in a few weeks (after MOT) and...

Was aware of this. Where is the best place to buy some?

What map is best to use with the following setup:- GruppeM, Fujitsubo RM01A catback, DC sports stainless header/decat. & GruppeM, Fuji RM01A without the header (mot time) ?

Also will i need to replace any gaskets?

Currently running GruppeM with Fujitsubo RM01 catback. Looking to install KPRO and a DC manifold. Am i correct in thinking that I can install the replacement manifold and use the existing 02 sensors. Will also need to fit rear engine mount. When Kpro installed I can run the RSX map with...

I have a RM01-A as it sounds just right. At tickover it has a slightly louder pur and then just a little louder when you put your foot down. I will try and do a vid sometime.

The tree of knowledge has spoken. Amen. thanks.

I have ordered some mugen pedals for my facelift CTR and understand it is easier to fit the accelerator pedal on a pre facelift pedal which is also on its way. How easy is it to remove/refit accelerator pedal? Anyone got a How to..?

Anyone know whether you can fit a spoon ETD and J's racing strut on together? they both bolt onto the offside strut bolts but will be close to the end of the thread with both mounting brackets in place. Anyone else had this combo and did you have any problems?

I am running this group buy on the CTRO forum. I know the GB has closed but i know the supplier has a few spare if anyone wants to join. Drop me a pm.

I might be interested in the Kpro, race cat and manifold if you decide to sell the mods seperately. PM me a price and your location if this is what you intend on doing.

Are the suspension struts identical on the pre and facelift CTR?

If they dont I may be interested in the camber bolts/adjustors for my EP3. :D

How loud would this setup be without the header and decat?