Search results

...

Well I think it has a MAP? Unless they built Keihen from standard but the car produced 221BHP on Dyno before any mods. Thanks

As I'm selling my CTR and believed it had a MAP a lot of people are asking me what MAP? So I've taken a look and it's labeled "KEIHEN" are they any good? Any advice, costs etc... Many Thanks

Just wondering where the ECU location is as I'm selling my car and believe it has a Hondata ECU. Thanks

Will do bud. There are some Tegiwa ones on there website for like £50 in black not sure in red.

I'm looking to purchase longer wheel nuts for my CTR. D1 on eBay are like £40 roughly but my mate said they are terrible and I want longer wheel nuts. Does anyone suggest anywhere cheap and cheerful as you've also got to purchase the washers which are like £21. Many Thanks

Don't see what the issue would be second hand, it will do just as good as a job apart from a few rusty bolts which you could easily replace. Well I'll be selling mine anyways just got to remove it. :)

What size are the vacuum hoses on the CTR? All near the manifold pretty sure they are all the same size? I was guess 4mm? Looking to order fresh red hoses. Many Thanks

Not sure between £30/£40 maybe.

There is mine in Gold. Instragram: DannyCoakley1990

Mine will be removed tomorrow :-)

Thank you mate, I have MOT next month so I may just leave it to the MOT and see the advisories and failures and buy the parts which I have 7 days to repair. Thanks

I think it's held in support to the brace. I'll take a picture tomorrow and upload. Thanks

Looking to remove it as it's doing my head in lol. Very little rattle. I was thinking about sticking a rubber grommet between it to stop the movement but may just be best to remove. My question is, if I was to remove it is there anything which shouls replace it's place or not? Its bolted to the...

Not to sure if I'm placing this under the right option but I habe creaking coming from my steering? When I am at a stand still for example and I turn the steering wheel say 2-4 inches either way it creaks or when coming to stand still it creaks? Any suggestions? I was thinking WD40 the whole...

Jusy wondering will it be okay to remove the manifold shield behind the engine block? I believe it's rattling like mad and when im driving its doing my nut in. Many thanks :)

What's best used to get that real deep black on your tyres? I tend to use back to black but looks shinny and doesn't last very long and believe it sprays up on the side of your car when driving? Thanks :)

To be honest I think its me being paranoid. Case closed thanks for all the help and support guys. Much appreciated

I don't infact think it needs tightening. Basiclly what im occuring now since I cleaned the ICV is a splatter from the exhaust. It sounds simular to when you don't have enough fuel. I hope this slightly explains it. Very slight hiss from the induction too.! Agro! Cheers

Does anyone know what that sensor is called above please? Also since removing the TB it seems that my cable is slightly slacked? How can I tighten it up? Many Thanks

Done that now regards to the sensor how do I remove that as the screws are weird. I also snapped this :(

Do I undo these 2x bolts?

I just really hope this is the issue.! If it is send me your paypal I'll send you a little drink to say thanks lol. I don't mind the cost as long as it's within budget its just finding the peoblem. Do u have FB? I can upload a video from my mobile. Thanks bud

Not hard to do and easy to re assemble? It's also okay to keep the battery disconnected over night? Sorry just that never really worked on a jap car used to finding faults on a VW. Thanks

The one you have to remove when you clean the ICV? Thanks

How do you remove the sensor from the ICV? Thanks

I meant how do you remove the throttle cable from the TB? Thanks

I couldn't see any bolts holding it on.. I'll have another look later. Whats the liquid in those hoses? Thanks

Hello mate. Quick update: I removed the TB. Undone 1 pipe and green liquid came out? Whats the coolant? Plus I cant remove the TB as the cable is attacthed so do I twist the TB then unscrew the screws by phillips then remove the ICV and leave the TB hanging? The gasket was shot too so ill buy...

I hope so, I don't mind the cost its just bugging now knowing the fault. Once it's found I'll be in a better mood. Can WD40 be okay to use on the IACV? Toothbrush too ? Any suggestion. Thanks

It bounces about from cold and warm. It's like it revs to 2,000k as it should from cold then goes to die then kicks in again to 2,000 then vice versa. It's so annoying and if your inpaticent like me I just want it sorted and done. My partner is going out tonight and won't be back till 10:30 or...

No warning lights or nothing. It's really odd! Liturely this morning started her up, bouncing of the limiter to around 2,500 in a calm way up and down and possibly may go slightly higher and louder with a more constant stay for a split second but where the exchaust is noisey I don't want to...

Also if it was sticking wouldn't it remain at a certain rev instead of bouncing? Cheers

I snapped the throttle cable a while ago but still works fine I thought... How can I check is this is faulty bud? Timming chain suggestions where online, but the engine is as quiet as a mouse! Cheers for your help mate I do really appreciate it. Hate taking the car to a garage unless its...

Don't say that mate I can't afford a new chain or hear a valves gone or something lol. If need be my £300 wheel money I have can only fix this. Also when driving and changing gear not sure if this is down to the funny idle but dropping the clutch the revs raise too?

Cheers for your reply Loxy! It doesn't struggle to idle it's full of beans just idle's radiculously! Going up and down with a hissing sounds from the induction kit. It's a HKS which cost like £250. Shall I spray like WD40 all round the TB and intake hose etc... Didn't think there was that...

I live down the lanes in the country side and I was bored last night (GF WENT TO SLEEP EARLY) so decided to give the car run. Vtec a few times and came to a tunnel and reved the car and the car started ideling funny reving itself low range up and down, up and down. I'm confused to what this is...

I've had delivered my OMP HT paint but wondering is it wise to use Primer and Laqure? I don't want 2 months down the line for the paint to peel due to the primer. I do want a glossy finish. Also I see people mention about putting it in the oven?? What temp and how long? Thanks :)

Yeah still retracts smoothly bud. The whole rubber came off now. So not sure what that now means... Thanks for your reply.

Love those wheels specially in gold. :)

Re: Milano CTR cars going :( Love the bright green rocker cover. Looks very clean! :D

When's the car getting sprayed?

I love the new shape Type R. Specially in white! :)

Re: EP3 Pete's Eerrrmmm...EP3 :D Awesome rocker cover. :thumbup:

Nice motor. :thumbup:

Does this mean my caliper is fuc*ed? Thanks

How can you tell if the rear caliper is shot? New pads and disc's and seems to lock up causing no wheels movement unless driving? Piston is correct and pads have been correctly fitted? Thanks

Manchester Ares yes. It's normal on renewals to always increase as a lot of people don't have time to check or look and think they will be cheaper. Genually look online and find cheaper they should price match. A fault claim in the same year as your renewal is due will be sky high. Go on a...

I work for a car insurance company depending who you are with most companies account for 9 or more years and a few do maximum of 5 either way you'll drop 2 years so down to 3 or down to 7. 90% sure it will be 7 in all honesty after losing 2 years NCB. It looks like a write off as I think they...

Easy to remove only 4 bolts or just undo the two and do the main caliper. Once the wheel is off it will become clear. The extra time should see a perfect job. Doing mine soon Orange :) Sent From My Samsung Galaxy S3

I've just lost my locking wheel nut so I can't do anything for a while lol. MOT in march so get that out the way first see if it passes if it fails or any advisories then I'll work on it if it comes up. Thanks bud Sent From My Samsung Galaxy S3

Yeah bud the little pip was within the cross of the piston. Makes no sense eh? Cheers for your input. :thumbup: Sent From My Samsung Galaxy S3

Yeah a 90º angle. I wound it all the way back exactly as the other one. Only thing I can see it down to possibly is that the new pads are slightly thicker? It's not a massive problem as sort of sorted but annoying. Thanks for your reply :) Sent From My Samsung Galaxy S3

2001 Honda Civic Type R Mileage: 154,000 Sent From My Samsung Galaxy S3

Hello all new to this forum. Searched all the online forums and seem to be more interested in this site. Basically on my way back from Center Parcs which is a 3 and half hour drive. Random man at the services on the M25 told me about the noise. The car was parked up for 3/4 days with no...

82,000 Miles FSH from Honda apart from the last service at like 79k which wasn't done by Honda. Thanks

MilanoBerry, did the 5W 40 do the trick as I'm suffering from the same problem. Thanks

Hello, all. I've just purchased my first Type R and I can tell you I've feel in love. I have chosen to keep the car and ditch the GF lol. On a serious note I thought it was the timming chain as that went on my Corsa and wasn't a lot of money. Well spoke to my Mechanic and told me different on...