Search results

hi guys a random question here does anybody know what type of pins are used on Hondas wiring looms, are they just standard Molex pins or are they specialised to honda, i am only asking because I have done a wire tuck on my ep3 were I have extended cables by soldering and heat-shrinking but I...

Hi guys urgent information needed, I brought a second hand hondata k100 which was mapped to a k24, with drag cartel camms bigger injectors and many other mods, my car is now booked in for a remap, on the 10th of September how ever, I have been told it will need to be recoded by honda first...

hI guys I have just fitted my dc sport 4-2-1 header and now my exhaust sits really low (possibly due to the flexi) and it's causing my backbox to melt the rear bumper, will this be a easy solution to fix or will I need something re fabricating

Hi guys I have tried searching for a post already on this, but couldn't find one, Does anyone know roughly how much heat wrap they used to wrap a 4-2-1 header for a ep3 Thanks in advance

Hi guys I have brought a DC-sport 4-2-1 header which needs welding doing to it and I didn't realise it was going to cost so much to replace, does anybody know if the unbranded stainless ones are any good as I have seen one very cheap and I'm not sure weather to buy it and sell the DC-sport one...

Hi guys, i am wanting some advice please I have owned my ep3 for a little while now and when I started off with her I had very small plans, and of course like everyone who tinkers with cars they go astray and I have done loads to her and she still isn't were I want her, how ever as of today I...

Hi guys as per title i have been offered a RBC intake and a KPro ecu for £750 would you say that's a good deal for them

Hi guys, I removed my exhaust yesterday, to replace with a new system and now 2 of the 3 studs on the cat are knackered, I cannot bolt B-pipe back on as a temporary solution I have had to seal up as best as possible with fire seal, had any any one had this issue and could they tell me the best...

Hi guys I have recently purchased a HKS Hi power exhaust for my ep3 please can anybody tell me what gaskets I will need or send me a like to a page I assume I will need 3 gaskets 1 from the cat to the b-pipe 1 from the b-pipe to the silencer and 1 from the silencer to the back box thanks guys

Hi guys one of my front drop links to the front ARB has recently snapped and I have been looking at Hardrace, or tegiwa or any poly bushed drop links, is it worth me buying them as my suspensions setup is completely standard, or shall I go for oem or a cheap pair from a local autoparts store...

Hi guys I have been looking at buying a exhaust header for my ep3 and have looked at the spoons Headers from the web site below http://www.eightspeed.co.uk/acatalog/EP3_Manifolds_Down_Pipes_and_De-Cat.html REF 920 REF 921 has any one ever fitted the bottom half to a dc5 upper half and what's...

Hi guys I've just posted else were but I've just had my ep3 dyno'd and it ran 195bhp with a 2.5" m2 silenced center section and m2 back box and tegiwa intake. The dyno guy said that vtec didn't sound right and sounded different to the 3 other ep3 there and one ep3 ran 220 with a cheap ebay air...

Hi guys a very sad day for me I went to a dyno day today and my ep3 ran very poorly compared to 2 others and a dc5 the guy said my vtec wasn't sounding right compared to the others and also apperently I had the better mods I have a tegiwa M induction kit and a m2 2.5" silenced center section and...

Hi guys I have just brought I tegiwa intake and replaced my typhoon with it,I was just about to take it for a test drive with it and my car started revving to the limmeter so I quickely switched it off turned it back on and it was revving to the 6k limmeter any idea what's cause it to do this I...

Hi, can any one tell me if the HKS hi power back box fit a non hks aftermarket center section, I have a 2.5" s/s center section and have been offered a hks back box which I really want, also how much would you say the value of the hks back box is thanks

Hi people not sure if it has been asked before but I have been looking at the rywire tuck looms and they look very smart but does and one know if there is a uk company that makes these looms thanks

Hi people, can any one give me any info on replica recaros, does any one have a set of reps are they cushy to they las ect. Any info will be great thAnks

Hi people I have been offered an eBay special exhaust one of these m2 exhaust the chap selling it is selling it really cheap and in brand new condition had any one brought one of these exhaust or can they give me a bit of info on them just by looking on ebay they just look like reps of decent...

Hi All i have found a Double din Facia for the CTR EP3 for £16 and that includes postage which is a bargin as most places are selling them for around £40 the Facia is Connect 2 CT23HD19 and the website is http://www.audioimages.co.uk/ hope that helps guys =)

Hi All, just wondering if any one has fitted plasma dials to there EP3's and if so have they got any pictures, i have fitted them to my corsa GSi and they look amazing, infact as my GSi is currently stripped my dials are on the shelf like an ornament =P

Hi Here is My 2004 Honda Civic Type R EP3 i bought this car as i no longer do the miles that i used to do, so the extra fuel cost and insurance wasnt an issue, this is my daily driver car even though it will hardly be used weekdays and only really on the weekends when i dont work, the car is...